I need some help fellas

I'm think'n of get'n into reload'n. If someone on here could explain to me what everything is used for and the equipment i'll need(i know primers,brass,bullets). Right now i'm look'n at an RCBS RC supreme master reloading kit from cabelas its $270. It comes with an RC supreme press, 5-0-5 powder scale, Uniflow powder measure, Speer No 14 Reloading Manual, hand-priming tool, hex key set, case loading block, case lube kit, powder funnel, and deburring tool. I'm go'n to get an electronic caliper for $28 from cabelas,Do i need a bullet puller?,I'm get'n a RCBS Trim Mate, and some dies. What else do i need, i'll be reload'n either 270 win, or 300 RUM
6,234
Default Avatar
Maybe a primer pocket cleaner and I personally like my vibratory cleaner to get all the dirt and case lube off my cases. The Speer handbook is a good one. Read it thoroughly. Usually your best loadings are going to be with a powder that fills the case nearly full to the base of the bullet. If at all possible get together with someone that has reloaded for years and has no disfiguring injuries. Most guys learn best when shown how to do something as opposed to reading about it.
Mark
16
silvertip-co
Best thing to do is get a reloading manual BEFORE you invest in tools, equipt, matls. READ the manual so you know what reloading is all about, then decide what tools, tips, techniques will work for you.
Hornady and Sierra make great manuals,well worththe 40.00 investment.I got my Hornady in 1971 when I was beginning reloading and still use it every session. Used manuals are avail for a good price on eBay.BEWARE ...older loading manuals have hotter loads than 2008 manuals and those loads MAY not be suitable in your particular rifle. And good luck reloading is a great hobby.
16
Default Avatar
I agree about getting the manual first. Then when you get the kit, add a case trimmer. All the caliper will tell you when you get one is if your cases are to long unless you also get the trimmer. Also go for an inertia type bullet puller. With a bit of practice you can save the bullets with one. I have both but haven't used the die puller in years.

A word of caution, keep your cases trimmed to under the max length. To long cases will jump pressure.
16
lifetime hunter
well.. like my Dad always said.. might save U some money.. but when ur see a big ol buck.. U sneak up on it.. raise UR gun.. slide the safety off.. aim ... click.. ](*,) BEEP $&*#&$ $HIT.. not worth it to reload Rifle loads!!! haha lol
16
Loke
"lifetime hunter" wrote:well.. like my Dad always said.. might save U some money.. but when ur see a big ol buck.. U sneak up on it.. raise UR gun.. slide the safety off.. aim ... click.. ](*,) BEEP $&*#&$ $HIT.. not worth it to reload Rifle loads!!! haha lol
 I've handloaded tens of thousands of rounds of ammunition, and never had a misfire. If you keep your greasy fingers off of the primers, and pay attention to what you are doing (like double check the powder levels in the case), you won't have a problem with the reliability of your handloads.
16
Default Avatar
I had a couple miss-fires many years ago. Learned to never touch primers with my fingers. But miss-fires can happen with factory stuff also. Not always the ammo's fault. could be in the bolt. crud build up can keep the fireing pin from hitting the primer properly. Also excessive headspace can allow the fireing pin to move the case enough in the chamber to not fire. Don't assume a miss-fire is always caused my reloads.
16
Default Avatar
The only misfires I've had were with cheap 22 ammo. I reloaded for over 40 years and never had a problem. Some years when I shot handguns for fun and competitively I loaded nearly 40,000 rounds a year and not a misfire. Be sure to store your components properly and never get WD-40 or penetrating oil near your ammo or primers. Keep your firing pin and bolt free from excessive oil too it will creep into the bolt face and may kill the primer.
Mark
16
Mack Daddy Muley
I reload and do not like RCBS for rifle reloading. I prefer Redding. I reload each casing seperatly. Each charge is weighed seperatly then dipenced into the case. Better accuacy! I have had problems with RCBS. And yes you should have a bullet puller. If you are mass producing like with a pistol, I'd use Dillon. RCBS just doesn't hold up well.
16